Use this article to understand optimum network requirements for your Blink devices.

Wi-Fi Network Requirements

• 2.4GHz Wi-Fi Network 802.11b/g/n 
• A high-speed internet connection (DSL, Cable, Fiber) with a minimum upload speed of 2 Mbit/sec.
• IP Configuration: DHCP 
• Wi-Fi Security: WEP, WPA, WPA2 with TKIP SSID

Note: Blink does not support satellite internet due to high latency issues.

Things to check first

Start with the following:

• Verify signal strengths. Blink App > Device Settings > General Settings > Camera to Wi-Fi will show your device's signal strength.
  • Find out more in the Network layout and Connectivity sections below.
• Power cycle all devices that allow connection to the internet.
• Verify your internet connection and account are active.

Network layout

Connectivity

Network frequency

Password

1. Often, when adding a camera or Sync Module to your Blink system, the password is mistyped. Try carefully re-entering your password. If you continue to receive the "Incorrect password for Your W-Fi" message, try the next steps.
2. Verify the password by checking if it's written on a sticker located on your router. 
3. Try forgetting the Wi-Fi network on your mobile device's network settings, and then reconnect to it. If you can successfully reconnect using this method, your password is correct.

• iOS users: How to forget a Wi-Fi network on iPhone, iPad, or Mac
• Android users: Remove saved networks

Router settings

Make sure that your router is not blocking access to the Sync Module. This can happen if you are alerted that a device is attempting access but the name is not familiar. Blink devices are sometimes identified by their radio chip instead of the Blink product name.

Disable VPN

Do you use a virtual private network (VPN) on your mobile device?  If so, please disable the VPN before you set up Blink devices. You can enable your VPN after you complete setup.

If you're continuing to have issues with VPN after setup, make sure your VPN server is in the same time zone as your device.

Important information to discuss with your Internet Service Provider (ISP)

We suggest speaking with your ISP to discuss your home network capabilities. Here is a guide for reviewing your network setup with your ISP.

• Upload speed - The Blink system requires a consistent minimum upload speed of 2Mbps per device. Any result lower than 2Mbps may cause latency and/or issues establishing or maintaining connection.
• Network congestion - The more devices in your home use Wi-Fi, the more they will be sharing your network's bandwidth. You can disable the Wi-Fi setting for non-Blink devices not in use and reenable it as needed.
• Old routing equipment - What is the age/model of your router? We recommend a router model less than 5 years old to ensure it supports the latest technology. If you're renting network equipment, your ISP may be able to provide you with an upgraded model at no additional cost.
• Packet loss - This means bits of information are being dropped when communicated over the network. This can cause communication failure from your device to your router or your mobile device to your router. Packet loss can occur within your home (device to router) and/or within your connection from your router to your ISP's server.
• Privacy settings/Parental Controls/Firewalls - Network security is important. Ensure these settings are set up so they do not interfere with your ability to connect to your connection to your Blink system. Ensure that each individual Blink device is allowed to establish its own connection. Tip: you can white-list your Blink device's individual MAC addresses. If you are unsure how to do so, check with your ISP.
• Duplicate SSIDs - When two networks in the same location have the same SSID/name, your Blink system may try to connect to the wrong one. This other SSID may be in a different location that is too far for reliable connectivity or may be and incompatible network. Ensure you are attempting to connect to the appropriate SSID.

Wi-Fi 6, also known as Wi-Fi 802.11ax is a new wireless technology being implemented in new routers.

Blink devices (Camera and Sync Module) require the use of an 802.11b/g/n network. Blink devices do not support the upcoming standard Wi-Fi 6 (802.11ax), but those new routers are backwards compatible with 802.11b/g/n, so Blink will continue to function as it does today.

Compatibility List:

Wi-Fi Password Troubleshooting

If you encounter an "Incorrect Password for Your Wi-Fi" alert while adding a camera or Sync Module to your Blink app, attempt the following troubleshooting steps:

1. Re-enter Wi-Fi Password: Double-check that you've entered the correct Wi-Fi password, and try again. If the "Incorrect Password for Your Wi-Fi" alert persists, proceed with the next steps.
2. Check Password on Router: Check your router for a sticker containing the Wi-Fi password. Keep in mind, some routers might not have this sticker.
3. Forget and Reconnect Wi-Fi Network: On your mobile device, go to network settings and choose to forget the Wi-Fi network. Then, try connecting to it again. If you can reconnect successfully, it means the password is correct.
   • iOS users: How to forget a Wi-Fi network on iPhone, iPad, or Mac
   • Android users: Remove saved networks

Special Characters in Your Wi-Fi Password

Using special characters (e.g., *, @, $, #) in your Wi-Fi password can sometimes create challenges during the initial setup of your Blink device. If you encounter any problems after confirming that your Wi-Fi password is correct, as outlined in the steps above, attempt the following troubleshooting steps:

1. Temporarily change your Wi-Fi password: Temporarily change your Wi-Fi password, ensuring it does not include any special characters.
2. Create a temporary guest network: Create a temporary guest network specifically for setting up your Blink device. After successfully setting up and connecting your Blink device to the internet, you can remove the temporary or guest network without impacting the device's functionality.

If you change your Wi-Fi password at any point after the initial setup, you must also update the password on your Blink devices and any other devices that connect to your Wi-Fi network.

When adding a Sync Module, Mini, Video Doorbell, or Wired Floodlight Camera, you will be prompted to connect your Blink app to the temporary Wi-Fi network. It is named “BLINK-" followed by the last four digits of the device's serial number. 

The Sync Module manages communications between your Blink devices and our secure servers; therefore your camera needs to connect to its local Wi-Fi. The Blink Mini, Video Doorbell, and Wired Floodlight do not require Sync Modules for those communications, which is why they broadcast their own local Wi-Fi connections.

It is completely safe to connect your mobile device to your local "BLINK-XXXX" Wi-Fi connection and there are no security issues. If you encounter any problems connecting to your local Blink Wi-Fi, make sure you have the Blink app Local Network (iOS) or Location (Android) permissions enabled on your mobile device. See the links below for more information.

iOS

Learn more about enabling Local Network for your Blink app on your iOS device.

Android

Learn more about changing the Blink app permissions on your Android device.

The camera in the Wired Floodlight Camera has a reset button at the top, which is not visible from the ground when it's mounted. This button can put the camera in setup mode to be added to a new or existing system or to a new Wi-Fi network. 

• Short press (less than 5 seconds) resets it and resolves most setup issues. 
• Long press puts the camera into setup mode. This also erases your Wi-Fi credentials; therefore, you need to enter your network name and password again to reconnect to your Internet.

If you receive a Camera is offline message on your Blink app home screen, it means the Blink servers lost communication with your Mini camera. This will normally fix itself when the network comes back up, or when there is less traffic on the Wi-Fi network. When your camera comes back online, the message will disappear.

Most often, disconnected or slow internet makes the Mini camera lose contact. Most internet providers provide downloads to your location much faster than uploads from your location. If there is a sudden jump in the data being used, the Mini camera may miss a check-in and the offline message may appear.

If your camera keeps disconnecting even when power and Wi-Fi internet are steady, please contact Blink support.

Troubleshoot Mini camera offline message

Check Power

The Blink Mini compact camera is powered by direct connection to a USB standard power adapter instead of batteries. To function, the power cord must be reliably connected to a 5 volt 1 Amp power source, and the molded USB connector must be fully inserted into the camera.

Check Internet

To send you images and sounds, the Mini camera needs a 2.4 GHz Wi-Fi internet connection with upload speeds (going out from your network) at least two megabits per second (2 Mb/sec) at all times, including when others are on the same internet connection.

When you tap the alert shown in the app home screen, a Camera Offline screen provides helpful tips. The first, is to check the Wi-Fi internet and the power supply, then check the camera power connection.      

Troubleshooting Wi-Fi

1. Check Wi-Fi. Ensure that you can connect to the internet, and that the password has not been changed. If the password has been changed, refer to the next step.
   Rebooting the Wi-Fi router is often very effective to resolve Blink connectivity issues.
   If you have rebooted your router and Blink does not connect after 3 minutes, continue.
2. Check your password. If the password is changed, or if you wish to use a different Wi-Fi network, tap the Change Wi-Fi button:     Change Wi-Fi     and follow the instructions.
   If the password or network have not changed, continue.
3. To repeat the camera installation process, tap the Delete Camera button:    Delete Camera   and follow the instructions.

If these steps do not reconnect your camera, please contact Blink support.

Learn how to get your doorbell back online or connected to Wi-Fi.

Remove or replace batteries

If the doorbell falls offline or it can't connect during setup, try these steps.

• Remove the batteries from the doorbell for 5 seconds and then re-insert them. 
• If the red LED flashes, press the Reset button on the back of the doorbell for five seconds. Your doorbell is now ready to be added to your Blink account.
• If no red LED flashes, try new batteries. Replace the batteries with two new, AA 1.5-volt lithium non-rechargeable batteries. If no red LED flashes, please contact Customer Support.

Reboot your router and check your Wi-Fi password

If the doorbell can't connect to your Wi-Fi network, try these steps:

• Reboot your Wi-Fi router - Unplug your Wi-Fi router for 30 seconds and plug it back in. Restarting your router can help when your Wi-Fi is slow or stops intermittently.
• Check your Password - Ensure you have entered your Wi-Fi password correctly. Tap the eye icon in the password field to see the password you enter. To learn more, visit My Wi-Fi password doesn't work.
• Check the connection between your Wi-Fi router and your doorbell - If your internet speeds are good, you may still have an issue with the strength of the signal between your router and the doorbell. To verify signal strength:
  • Tap the More iconat the bottom right of the doorbell's thumbnail image and select Device Settings. 
  • Tap General Settings.
  • Locate Network and confirm the Connection to Wi-Fiis sufficient.
• If these steps don't work try disabling your VPN on your mobile or uninstall any apps that may conflict with the Blink app.  Learn more about conflicting apps.

Learn more about Blink Wi-Fi Network Requirements.

Poor connectivity with Blink severs

You may receive an in-app message alerting you to poor connectivity to Blink servers. Be sure your internet connection is working and that it can provide a minimum of 2Mbps of upload speed. 

Sync Module placement

If your doorbell is connected to a Sync Module, consider moving the Sync Module to provide better signal strength between the Wi-Fi router and the doorbell. To check your Sync Module signal strength, follow these steps.

1. Tap Device Settings > General Settings.
2. Under Network, the signal strength of the Sync Module to the doorbell is displayed.
3. If your signal strength is two bars or less, you may need to bring the Sync Module closer to the doorbell.

For more information, visit the "Where to Place your Sync Module" section of Understanding Blink Wi-Fi Requirements.

Delete your Doorbell

If you've attempted the troubleshooting steps listed above but are still experiencing issues, try deleting and re-adding the doorbell to your Blink system.

1. Tap the More iconat the bottom the doorbell's thumbnail image and select Device Settings.
2. Tap General Settings. 
3. Tap Delete Device.
4. When the confirmation message displays, tap DELETE to remove the doorbell. 
5. After you tap DELETE, you will receive an email confirming the doorbell has been deleted from your account.

Once your doorbell is removed from your account, you can re-add it back to your Blink account. Learn more about setting up your Video Doorbell ‍.

If one of your Blink cameras isn't responding, you may see error messages such as "Camera Busy" or "Thumbnail Failed." 

These messages can happen if your Sync Module isn't able to communicate with the camera.

The following steps may also help in resolving this issue.

1. Move your camera closer to your Sync Module. Also make certain that you have 3 bars of signal strength for Camera to Wi-Fi and Camera to Sync Module (see "Where to find signal strength in the Blink app" below).
2. Power cycle both your modem and router by unplugging them for 30 seconds and plugging them back in. Then wait two minutes for Internet service to be restored and then try using your camera again.
3. Power cycle your camera by removing the batteries for 10 seconds and reinsert them. Then check to see if your camera responds to commands.
4. If the steps above don't resolve the issue, try a different power source. You can use a micro USB cable and USB power adapter to power the camera with the batteries removed.

How to resolve connectivity issues

If you continue to experience issues, please contact Technical Support to assist you further.

If your Sync Module is offline or if you encounter any issues during setup, begin by verifying the LED patterns on the device. Then, proceed with the troubleshooting steps outlined below:

Solid Blue / Blinking Green LED

If your Sync Module displays a solid blue and a blinking green LED, this indicates the Sync Module is offline and attempting to reconnect to the previously configured Wi-Fi network.

Several reasons why your Sync Module may have gone offline include power interruptions (such as outages or being unplugged for a prolonged period of time), updated Wi-Fi settings (such as a new password), or signal interference from devices like pods and extenders.

If your Sync Module goes offline, you will notice the following in the Blink app:

1. A "Sync Module is Offline" banner will appear at the top of the home screen.
2. The thumbnails of each camera will blur and display a "Sync Module is offline" message in the center.

   

Before you attempt troubleshooting, please verify:

1. Network Compatibility: Your network meets the requirements necessary for Blink devices as outlined in Understanding Wi-Fi and Network Requirements.
2. Wi-Fi Password: Your Wi-Fi password has not changed since you last set up your Sync Module. If it has changed, you will need to update the Sync Module with the new Wi-Fi password. For guidance, visit Updating the Wi-Fi Setting for Your Sync Module System.

After confirming the information above, if the issue persists, attempt the following troubleshooting steps:

1. Power-Cycle Your Router: Unplug your router from the power outlet, wait 30 seconds, and then plug it back in.
2. Power-Cycle the Sync Module: Disconnect the Sync Module from power for 10 seconds, then plug it back in. After rebooting, a solid blue and solid green LED indicates the Sync Module has successfully reconnected to the network.
3. Re-enter Wi-Fi Password: Refresh the Sync Module's Wi-Fi connection by re-entering your Wi-Fi password. For guidance on updating your Sync Module's Wi-Fi settings, visit Updating the Wi-Fi Setting for Your Sync Module System.
4. Simplify Wi-Fi Configuration: Disconnect any pods or extenders, and ensure that only your main router is powered on.
   Note: After your Sync Module connects successfully, you can reconnect any pods or extenders that were previously disconnected.

If the issue persists after following the above steps, you'll need to delete and re-add your Sync Module.

Solid Red LED

If your Sync Module displays a solid red LED during setup, it indicates that the Sync Module is unable to connect to your Wi-Fi network, or the entered Wi-Fi password may be incorrect.

Before you attempt troubleshooting, please verify:

1. Network Compatibility: Your network meets the requirements necessary for Blink devices as outlined in Understanding Wi-Fi and Network Requirements.
2. Sync Module Placement: The Sync Module is in the same room as your router, but not too close, ensuring it's also positioned away from physical obstructions to avoid network interference. For placement best practices, refer to Understanding the Placement of Your Sync Module.
3. Wi-Fi Password: The Wi-Fi password entered is correct. If you receive an "Incorrect Password for Your Wi-Fi" alert in the Blink app during Sync Module setup, re-enter the password carefully and try again. For additional troubleshooting, visit Troubleshooting Incorrect Wi-Fi Password in the Blink App.
4. No App Conflicts or Network Interferences: There are no apps that conflict with the Blink app, or any VPNs, firewalls, or anti-virus apps active or connected to your mobile device.

After confirming the information above, if the issue persists, attempt the following troubleshooting steps:

1. Power-Cycle the Sync Module: Disconnect the Sync Module from power for 10 seconds, then plug it back in. After rebooting, a blinking blue and solid green LED indicates the device is ready for setup. For additional troubleshooting, visit How to Reset Your Sync Module.
2. Power-Cycle Your Router: Unplug your router from the power outlet, wait 30 seconds, and then plug it back in.
3. Simplify Wi-Fi Configuration: Disconnect any pods or extenders, and ensure that only your main router is powered on.
   Note: After your Sync Module connects successfully, you can reconnect any pods or extenders that were previously disconnected.

If the issue persists after following the steps above, proceed with a factory reset of the Sync Module.

Sync Module LEDs

 

The LEDs on the Sync Module are located on the top of the device. Below is a chart explaining the meanings of the LED indicators, along with corresponding links to relevant support articles for troubleshooting.

Note: The light pattern is the same for both Sync Module (1st Gen) and Sync Module 2.

Light Pattern	Description
	LED: Solid blue Activity: Sync Module is starting up.
	LED: Blinking blue, solid green Activity: Sync Module is in pairing mode and ready to be set up.
	LED: Solid blue, blinking green Activity: Sync Module has fallen offline and is attempting to reconnect to the previous network.
	LED: Solid red Activity: Sync Module is unable to connect to your network, or the entered Wi-fi password may be incorrect.
	LED: Solid blue, solid green Activity: Sync Module is online and connected to your network.

Sync Module 2

The Sync Module 2 includes a reset button located on the back of the device, as shown below (#3).

Sync Module 2 Components

1. QR Code of the Device Serial Number (DSN)
2. USB 2.0 Type-A port for USB flash drive (for Local Storage)
3. Reset Button
4. Power port (standard mini-USB 5v 1A)

To reset the Sync Module 2:

Press and hold the reset button on the Sync Module 2 with a small, pointed object for five seconds. Release the button once the red LED begins to flash. A blinking blue and a solid green LED will appear, indicating that the Sync Module 2 is now ready to be set up.

Sync Module (1st Gen)

The Sync Module (1st Gen) includes a reset button located next to the USB port on the device.

To reset the Sync Module (1st Gen):

Use a small, thin object like a paperclip or a toothpick to press the reset button until you feel a click.